GPIO Board Parts

Bill of Materials - Digi-Key Order Form

MegaSquirt® V2.10 GPIO 4L80E w/ MegaShift™

This is the V2.10 GPIO component parts ordering form for Digi-Key, it was created by Dave Hjort based on the 4L60E BOM. It will allow you to assemble the V2.10 GPIO Board with just a printed circuit board (PCB) with the SMT components installed, the items in this bill of materials, and a case. Note that some additional parts will be required, as noted near the bottom of the form.

Quantities are as required for V2.10 GPIO 4L80E w/MegaShift™ build. .

Note: Normally you will order a complete kit from a distributor, this BOM is provided for reference only.

To order complete the following steps:

  1. Verify that you have the quantities you want for each item below.

  2. Then send your order to Digi-Key:

    You will be redirected to Digi-Key to confirm your order items and quantities. (Go to Ordering Homepage and "CREATE NEW ORDER" if you want to start over with an order after you have submitted it.)

  3. Finalize your order by clicking on the 'finish order' button on the Digi-Key site. Verify your order, payment method, and shipping details. The order will not be complete until you have finished this step.

Qty.
MegaSquirt
Reference
Description
Digi-Key P/N
Unit
Price
Ext.
Price
per kit
I/O-CPU Header, 25x2, 0.100" 5.34 5.34
Jumpers, 0.100" 0.093 2.79
BootLoader headr, 0.100" 0.21 0.21
BDM Header, 0.100" 0.44 0.44
Optional Jumpers, 0.100" 0.68 0.68
Diode, 1A, 1N4001 0.136 0.68
Diode, 30V Zener 0.41 2.05
Diode, 5.6V Zener 0.41 2.05
Capacitor, 47pF, 200V, Radial 0.29 1.16
Capacitor, 0.001 uF, 100V 0.127 0.64
Capacitor, 0.1 uF 0.157 0.32
Capacitor, 1.0 uF, 50V 1.40 1.40
LM2937-5.0 Voltage Regulator 1.65 1.65
TIP120 Transistor 0.56 2.24
RFP30N06LE Transistor 0.89 0.89
Mica Insulator Kit, TO-220 1.75 14.00
Transistor, NPN 0.11 0.44
Resistor, 120 Ohms, 1/4W (CAN termination) 0.052 0.27
Resistor, 330 Ohms, 1/8W (Pullup Risistor) 0.052 0.27
Resistor, 1.0K Ohms, 1/8W 0.058 1.42
Bias resistor, 2.49K Ohms, 1% 0.098 0.49
Resistor, 10K Ohm, 1/4W 0.052 0.26
Resistor, 15K Ohm, 1/8W 0.052 0.26
Resistor, 33K Ohms, 1/8W 0.052 0.26
Resistor, 100K Ohms, 1/8W 0.052 0.26
Resistor, 680K Ohms, 1/8W 0.052 0.26
Resistor, 2M Ohms, 1/8W 0.052 0.26
Resistor, 4.7 Ohms, 5W wire wound 0.34 0.34
Sub-
total		 Shipping and processing may be extra, depending on your location and order size $41.33
Here are the other parts you'll need to build your GPIO: Some MegaSquirt® Related Links:
Printed Circuit Board (PCB) with SMD components installed, BDM and bootloader headers installed, and serial monitor loaded, connector and harness pigtail,

LMB-Heeger case - EAS-400 These are tall cases that will fit both a MegaSquirt® and a GPIO board. Or your own custom enclosure

Serial Cable: If you do not have an appropriate serial cable (such as the one from a Innovate LC-1, or MicroSquirt® EFI controller, or as supplied with production GPIO units), you will also need:

  • Serial Jack Cable, CP-254CS-ND, $5.04
  • DB9 Serial Connector. 4109FE-ND, $3.36
  • DB9 Serial Connector Hood, 976-09RPE-ND, $1.39

MegaShift™ Site

GPIO Forums

MegaSquirt FAQ

NOTES:

This BOM uses the updated VSS circuit

Click here to go back to the MegaSquirt® FAQ
MegaSquirt® and MicroSquirt® controllers are experimental devices intended for educational purposes.
MegaSquirt® and MicroSquirt® controllers are not for sale or use on pollution controlled vehicles. Check the laws that apply in your locality to determine if using a MegaSquirt® or MicroSquirt® controller is legal for your application.
©2010 Bruce Bowling and Al Grippo. 4L80E changes thanks to Dave Hjort - thanks! All rights reserved. MegaSquirt® and MicroSquirt® are registered trademarks.